Effects of inspection errors on curiailed dorman-type procedures

The effects of inspection error on a two-stage procedure for identification of defective units is studied. The first stage is intended to provide the number of defective units in a group of n units; the second stage consists of individual inspection until the status of all units is (apparently) established     

An investigation of the effects of inspection errors on the run-length control charts

For continuous inspection schemes in an automated manufacturing environment, a useful alternative to the traditional p or np chart is the Run-Length control chart, which is based on plotting the run lengths (the number of conforming items) between successive nonconforming items. However, its establishment relies on the error-free inspection assumption, which can seldom be met in practice. In this paper, the effects of inspection errors on the Run-Length chart are investigated based on that these errors are assumed known. The actual false alarm probability and the average number inspected (ANI) in the presence of inspection errors are studied. This paper also presents the adjusted control limits for the Run-Length chart, which can provide much closer ANI curves to the ones obtained under error-free inspection.     

Exact calculation of the Dodge-Romig LTPD single sampling plans for inspection by variables

In this paper we shall deal with the acceptance sampling plans when the remainder of rejected lots is inspected. We shall consider two types of LTPD plans- for inspection by variables and for inspection by variables and attributes (all items from the sample are inspected by variables, remainder of rejected lots is inspected by attributes). We shall report on an algorithm allowing the calculation of these plans when the non-central t distribution is used for the operating characteristic. The calculation is considerably difficult, algorithm for non-central t distribution takes several minutes. For the calculation we shall use an original method.     

Procedure for the selection of CSP-M one level skip-lot sampling inspection plans that have a single-sampling plan with acceptance number zero as the reference plan

This paper presents a procedure for the selection of CSP-M one-level skip-lot sampling plans, designated as CSP-MSkSP, that have a single-sampling plan with acceptance number zero as the reference plan. The parameters of the plan are determined when two points on the operating characteristic curve are specified, the two points being (p1,) and (p2,), where p1 is the acceptable quality level, is the producer's risk, p2 is the limiting quality level and is the consumer's risk.     

Design and evaluation of skip-lot sampling inspection plans with double-sampling plan as the reference plan

This paper presents a design for skip-lot sampling inspection plans with the double-sampling plan as the reference plan, so as to reduce the sample size and produce more efficient plans in return for the same sampling effort. The efficiency of the proposed plan compared with that of the conventional double-sampling plan is also discussed. The need for smaller acceptance numbers under the plan is highlighted. Methods of selecting the plan indexed by the acceptable quality level and limiting quality level, and by the acceptable quality level and average outgoing quality level are also presented.     

Online control by attributes in the presence of classification errors with variable inspection interval

ABSTRACT

The procedure for online control by attribute consists of inspecting a single item at every m items produced (m ≥ 2). On each inspection, it is determined whether the fraction of the produced conforming items decreased. If the inspected item is classified as non conforming, the productive process is adjusted so that the conforming fraction returns to its original status. A generalization observed in the literature is to consider inspection errors and vary the inspection interval. This study presents an extension of this model by considering that the inspected item can be rated independently r (r ≥ 1) times. The process is adjusted every time the number of conforming classifications is less than a, 1 ≤ a ≤ r. This method uses the properties of an ergodic Markov chain to obtain the expression for the average cost of this control system. The genetic algorithm methodology is used to search for the optimal parameters that minimize the expected cost. The procedure is illustrated by a numerical example.     

Improved estimation of the population parameters when some additional information is available

Estimation of population parameters is considered by several statisticians when additional information such as coefficient of variation, kurtosis or skewness is known. Recently Wencheko and Wijekoon (Stat Papers 46:101–115, 2005) have derived minimum mean square error estimators for the population mean in one parameter exponential families when coefficient of variation is known. In this paper the results presented by Gleser and Healy (J Am Stat Assoc 71:977–981, 1976) and Arnholt and Hebert (, 2001) were generalized by considering T (X) as a minimal sufficient estimator of the parametric function g(θ) when the ratio t²=[ g(q) ]^-2Var[ T(X ) ]{tau^{2}=[ {g(theta )} ]^{-2}{rm Var}[ {T(boldsymbol{X} )} ]} is independent of θ. Using these results the minimum mean square error estimator in a certain class for both population mean and variance can be obtained. When T (X) is complete and minimal sufficient, the ratio τ² is called “WIJLA” ratio, and a uniformly minimum mean square error estimator can be derived for the population mean and variance. Finally by applying these results, the improved estimators for the population mean and variance of some distributions are obtained.     

Selection of single sampling variables plans based on the minimum angle

This paper provides single sampling variables plans for given values of n, the acceptable quality level and limiting quality level. Tables are constructed using the minimum angle technique.     

Testing process capability based on Cpm in the presence of random measurement errors

Process capability indices have been widely used in the manufacturing industry providing numerical measures on process performance. The index C_p provides measures on process precision (or product consistency). The index C_pm, sometimes called the Taguchi index, meditates on process centring ability and process loss. Most research work related to C_p and C_pm assumes no gauge measurement errors. This assumption insufficiently reflects real situations even with highly advanced measuring instruments. Conclusions drawn from process capability analysis are therefore unreliable and misleading. In this paper, we conduct sensitivity investigation on process capability C_p and C_pm in the presence of gauge measurement errors. Due to the randomness of variations in the data, we consider capability testing for C_p and C_pm to obtain lower confidence bounds and critical values for true process capability when gauge measurement errors are unavoidable. The results show that the estimator with sample data contaminated by the measurement errors severely underestimates the true capability, resulting in imperceptible smaller test power. To obtain the true process capability, adjusted confidence bounds and critical values are presented to practitioners for their factory applications.     

Use of prior information in the form of interval constraints for the improved estimation of linear regression models with some missing responses

We consider the estimation of coefficients in a linear regression model when some responses on the study variable are missing and some prior information in the form of lower and upper bounds for the average values of missing responses is available. Employing the mixed regression framework, we present five estimators for the vector of regression coefficients. Their exact as well as asymptotic properties are discussed and superiority of one estimator over the other is examined.     

Limit behaviors of the estimator of nonparametric regression model based on martingale difference errors

In the paper, we shall establish some limit theorems for the nonparametric estimator of the regression model, which include $L^p$-convergence, complete convergence, and strong convergence of the estimator. These results supplement and improve some known works.     

Sampling plans based on balanced incomplete block designs for evaluating the importance of computer model inputs

The importance of individual inputs of a computer model is sometimes assessed using indices that reflect the amount of output variation that can be attributed to random variation in each input. We review two such indices, and consider input sampling plans that support estimation of one of them, the variance of conditional expectation or VCE (Mckay, 1995. Los Alamos National Laboratory Report NUREG/CR-6311, LA-12915-MS). Sampling plans suggested by Sobol’, Saltelli, and McKay, are examined and compared to a new sampling plan based on balanced incomplete block designs. The new design offers better sampling efficiency for the VCE than those of Sobol’ and Saltelli, and supports unbiased estimation of the index associated with each input.     

Complete consistency for the estimator of nonparametric regression model based on martingale difference errors

Abstract

In this paper, we study the complete consistency for the estimator of nonparametric regression model based on martingale difference errors, and obtain the convergence rates of the complete consistency by using the inequalities for martingale difference sequence. Finally, some simulations are illustrated.     

Inference on C pk for autocorrelated data in the presence of random measurement errors

The present paper examines the properties of the C _pk estimator when observations are autocorrelated and affected by measurement errors. The underlying reason for this choice of subject matter is that in industrial applications, process data are often autocorrelated, especially when sampling frequency is not particularly low, and even with the most advanced measuring instruments, gauge imprecision needs to be taken into consideration. In the case of a first-order stationary autoregressive process, we compare the statistical properties of the estimator in the error case with those of the estimator in the error-free case. Results indicate that the presence of gauge measurement errors leads the estimator to behave differently depending on the entity of error variability.     

A note on the unification of the Akaike information criterion

To measure the distance between a robust function evaluated under the true regression model and under a fitted model, we propose generalized Kullback–Leibler information. Using this generalization we have developed three robust model selection criteria, AICR*, AICCR* and AICCR, that allow the selection of candidate models that not only fit the majority of the data but also take into account non-normally distributed errors. The AICR* and AICCR criteria can unify most existing Akaike information criteria; three examples of such unification are given. Simulation studies are presented to illustrate the relative performance of each criterion.     

Tobacco—the importance of relevant information on risk

Summary. Although it has been widely accepted since the 1960s that smoking cigarettes carries a substantial health risk, worldwide mortality from tobacco-related diseases is increasing rapidly at the beginning of the 21st century. To provide the motivation to control this epidemic there is a continuing and pressing need for information on the risks of tobacco consumption that is accurate, up to date, locally relevant and imaginatively presented.     

A note on the geometry of kullback-leibler information numbers

Csiszar (1975) has shown thdt kullhack-Leibler information numbers possess some geometrical properties much like those in Euclidean geometry. Thls paper extends these results by characterizing the shortest line between two ditributions as well as the midpoit of the line.     

A class of statistics based on the information concept

The methodic use of Shannon's entropy as a basic concept, complementing probability, leads to a new class of statistics which provides, inter alia, a measure of mutual dissimilarity y between several frequency distributions. Application to contin-gency tables with any number of dimensions yields a dimension-less, standardised contingency coefficient which depends on the direction of inference and will combine multiplicatively with the number of observed events. This class of statistics further in-cludes a continuous modification W of the number of degrees of freedom in a table, and a measure Q of its overall information content. Numerical illustrations and comparisons with former re-sults are worked out. Direct applications include the optimal partition of a quasicontinuum into cells by maximizing Q, the ordering of unordered tables by minimising local values of y, and a tentative absolute weighting of inductive inference based on the minimal necessary shift, required by an hypothesis, between the actually observed data and a set of assumed future events.