An optimal age-replacement policy for a simple repairable system with delayed repair

In this article, a simple repairable system (i.e., a repairable system consisting of one component and one repairman) with delayed repair is studied. Assume that the system after repair is not “as good as new”, and the degeneration of the system is stochastic. Under these assumptions, using the geometric process repair model, we consider a replacement policy T based on system age under which the system is replaced when the system age reaches T. Our problem is to determine an optimal replacement policy T*, such that the average cost rate (i.e., the long-run average cost per unit time) of the system is minimized. The explicit expression of the average cost rate is derived, the corresponding optimal replacement policy T* can be determined by minimizing the average cost rate of the system. Finally, a numerical example is given to illustrate some theoretical results and the model's applicability.     

An extended geometric process repair model with imperfect delayed repair under different objective functions

This article studies an extended geometric process repair model for a simple repairable system with imperfect delayed repair. Assume that the system after repair is not always successively degenerative, and the repair is not also always delayed. Under these assumptions, based on the failure number N of the system, an optimal replacement policy N* is determined respectively by minimizing the average cost rate (ACR), maximizing the average availability rate (AAR), and optimizing the trade-off model of the ACR and the AAR. Finally, a numerical example is given to illustrate some theoretical results and the model applicability.     

A geometric process repair model for a cold standby repairable system with imperfect delay repair and priority in use

In this article, a two-dissimilar-component cold standby repairable system with one repairman is studied. Assume that the repair after failure for each component is delayed or undelayed. Component 2 after repair is “as good as new” while Component 1 after repair is not, but Component 1 has priority in use. Under these assumptions, using a geometric process, we consider a replacement policy N based on the failure number of Component 1. An optimal replacement policy N* is determined by minimizing the average cost rate C(N) of the system. Finally, a numerical example is given to illustrate some theoretical results and the model applicability.     

An extended geometric process repair model with delayed repair and slight failure type

This article proposes an extended geometric process repair model to generalize the geometric process repair model and studies a repair-replacement problem for a simple repairable system with delayed repair, based on the failure number N of the system under the new model. An optimal replacement policy N* is determined by maximizing the average reward rate of the system. The explicit expression of the average reward rate is derived, and the uniqueness of the optimal replacement policy N* is also proved. Finally, a numerical example is given to illustrate some theoretical results and the model applicability.     

Heine process as a q-analog of the Poisson process—waiting and interarrival times

In this study, we introduce the Heine process, {X_q(t), t > 0}, 0 < q < 1, where the random variable X_q(t), for every t > 0, represents the number of events (occurrences or arrivals) during a time interval (0, t]. The Heine process is introduced as a q-analog of the basic Poisson process. Also, in this study, we prove that the distribution of the waiting time W_{ν, q}, ν ? 1, up to the νth arrival, is a q-Erlang distribution and the interarrival times T_{k, q} = W_{k, q} ? W_{k ? 1, q},?k = 1, 2, …, ν with W_{0, q} = 0 are independent and equidistributed with a q-Exponential distribution.     

Two-Dimensional Warranty Cost Analysis for Second-Hand Products

In spite of the recent steady increase of the volume of the second-hand markets, often customers remain in doubt regarding the quality and durability of the second-hand products. Aiming to reduce and share this uncertainty, dealers offer warranty on their products. Offering warranty for second-hand products is a relatively new marketing strategy employed by dealers of used electronic equipment, furniture, automobiles, etc. Usually, for used products, the dealer's expected warranty cost is a function of product reliability, past age and usage, servicing strategy and conditions and terms of the warranty policy/contract. Sometimes the offered policy is limited by two parameters, typically the product age and usage after the sale. This type of policies is referred to as two-dimensional warranty policies. In this article, we develop statistical models for estimating the dealer's expected warranty cost for second-hand products sold with two-dimensional free repair/replacement warranty.     

Pooling operators with the marginalization property

In this paper, we consider the problem of combining a number of opinions which have been expressed as probability measures P₁, …, P_n, over some space. It is shown that a pooling formula which has the marginalization property of McConway (1981) must be of the form T = Σⁿ_i=₁W_i P_i + (1 - Σⁿ_i =₁W_i)Q, where Q is an arbitrary measure and W₁, …, W_n ϵ [—1,1] are weights such that| Σ_J Σ _j w_j | ≤ 1 for every subset J of {1, …, n}. If, in addition, T is required to preserve the independence of arbitrary events A and B whenever these events are independent under each P_i, then either T = P_i for some 1 ≤ i ≤ n or T = Q, in which case Q takes values in {0, l}.     

Replacement policies for age and working numbers with random life cycle

It has been modeled for several replacement policies in literatures that the whole life cycle or operating interval of an operating unit should be finite rather than infinite as is done with the traditional method. However, it is more natural to consider the case in which the finite life cycle is a fluctuated parameter that could be used to estimate replacement times, which will be taken up in this article. For this, we first formulate a general model in which the unit is replaced at random age U, random time Y for the first working number, random life cycle S, or at failure X, whichever occurs first. The following models included in the general model, such that replacement done at age T when variable U is a degenerate distribution, and replacement done at working numbers N summed by number N of variable Y, are optimized. We obtain the total expected cost until replacement and the expected replacement cost rate for each model. Optimal age T, working number N, and a pair of (T, N) are discussed analytically and computed numerically.     

Some characterizations of discrete distributions based on weak records

Let X ₁, X ₂,... be iid random variables (rv's) with the support on nonnegative integers and let (W _n , n≥0) denote the corresponding sequence of weak record values. We obtain new characterization of geometric and some other discrete distributions based on different forms of partial independence of rv's W _n and W _n+r —W _n for some fixed n≥0 and r≥1. We also prove that rv's W ₀ and W _n+1 —W _n have identical distribution if and only if (iff) the underlying distribution is geometric.     

An (s,k, S) fluid inventory model with exponential leadtimes and order cancellations

We consider a stochastic fluid inventory model based on a (s, k, S) policy. The content level W = {W(t): t ≥ 0} increases or decreases according to a fluid-flow rate modulated by an n-state continuous time Markov chain (CTMC). W starts at W(0) = S; whenever W(t) drops to level s, an order is placed to take the inventory back to level S, which the supplier will carry out after an exponential leadtime. However, if during the leadtime the content level reaches k, the order is suppressed. We obtain explicit formulas for the expected discounted costs. The derivations are based on the optional sampling theorem (OST) to the multidimensional martingale and on fluid flow techniques.     

Optimal component test plans for a parallel system based on Type-II censoring

Consider a parallel system with n independent components. Assume that the lifetime of the jth component follows an exponential distribution with a constant but unknown parameter λ_j, 1≤j≤n. We test r_j components of type-j for failure and compute the total time T_j of r_j failures for the jth component. Based on T=(T₁,T₂,…,T_n) and r=(r₁,r₂,…,r_n), we derive optimal reliability test plans which ensure the usual probability requirements on system reliability. Further, we solve the associated nonlinear integer programming problem by a simple enumeration of integers over the feasible range. An algorithm is developed to obtain integer solutions with minimum cost. Finally, some examples have been discussed for various levels of producer’s and consumer’s risk to illustrate the approach. Our optimal plans lead to considerable savings in costs over the available plans in the literature.     

A probablistic analysis for an optimal screening problem

Summary We consider a lotL formed byN apparently similar unitsW ₁,…,W _N, where each of theW _i may come from one of two different populationsP ₁ andP ₂;T ₁,…,T _N denote the corresponding lifetimes. The units fromP _i undergo a failure of kindi and their survival function isS _i (t). We assume that the failure rate function are known and that the units fromP ₁ are ?substandard?: λ ₁ (t)≥λ ₂ (t), ∀t≥0. We want to putW ₁,…,W _N under a pre-operational test (burn-in test) in order to eliminate at least a great part of the substandard units and we face the problem of obtaining a rule for stopping the test under the assumption that, with the failure of a unit, it is possible to recognize the population from which the unit comes. Such a problem will be formalized as an optimal stopping problem for a suitably defined Markov process. Our study shall evidentiate some fundamental aspects of the problem and the role of the prior distribution of the (random) numberM ₀ of those units inL coming fromP ₁ (substandard). The latter distribution has a great influence on the form of the solution. This research was supported by the C.N.R. Project ?Statistica Bayesiana e Simulazione in Affidalità e Modellistica Biologica?.     

A Bivariate Optimal Replacement Policy for a System With Age-dependent Minimal Repair and Cumulative Repair-cost Limit

In this article, a repairable system with age-dependent failure type and minimal repair based on a cumulative repair-cost limit policy is studied, where the information of entire repair-cost history is adopted to decide whether the system is repaired or replaced. As the failures occur, the system has two failure types: (i) a Type-I failure (minor) type that is rectified by a minimal repair, and (ii) a Type-II failure (catastrophic) type that calls for a replacement. We consider a bivariate replacement policy, denoted by (n,T), in which the system is replaced at life age T, or at the n-th Type-I failure, or at the kth Type-I failure (k < n and due to a minor failure at which the accumulated repair cost exceeds the pre-determined limit), or at the first Type-II failure, whichever occurs first. The optimal minimum-cost replacement policy (n,T)* is derived analytically in terms of its existence and uniqueness. Several classical models in maintenance literature could be regard as special cases of the presented model. Finally, a numerical example is given to illustrate the theoretical results.     

The Variable Sampling Interval (VSI) in an Analysis of Taguchi's On-line Quality Monitoring Procedure for Variables

The procedure of on-line process control for variables proposed by Taguchi consists of inspecting the mth item (a single item) of every m items produced and deciding, at each inspection, whether the mean value is increased or not. If the value of the monitored statistic is outside of the control limits, one decides the process is out-of-control and the production is stopped for adjustment; otherwise, it continues. In this article, a variable sampling interval (with a longer L and a shorter m ≤ L) chart with two set of limits is used. These limits are the warning (±W) and the control (±C), where W ≤ C. The process is stopped for adjustment when an observation falls outside of the control limits or a sequence of h observations falls between the warning limits and the control limits. The longer sample interval is used after an adjustment or when an observation falls inside the warning limits; otherwise, the short sampling interval is used. The properties of an ergodic Markov chain are used to evaluate the time (in units) that the process remains in-control and out-of-control, with the aim of building an economic–statistical model. The parameters (the sampling intervals m and L, the control limits W and C and the length of run h) are optimized by minimizing the cost function with constraints on the average run lengths (ARLs) and the conformity fraction. The performance of the current proposal is more economical than the decision taken based on a sequence of length h = 1, L = m, and W = C, which is the model employed in earlier studies. A numerical example illustrates the proposed procedure.     

Economic and economic statistical design of T 2 control chart with two adaptive sample sizes

The Hotelling's T ² control chart, a direct analogue of the univariate Shewhart X¯ chart, is perhaps the most commonly used tool in industry for simultaneous monitoring of several quality characteristics. Recent studies have shown that using variable sampling size (VSS) schemes results in charts with more statistical power when detecting small to moderate shifts in the process mean vector. In this paper, we build a cost model of a VSS T ² control chart for the economic and economic statistical design using the general model of Lorenzen and Vance [The economic design of control charts: A unified approach, Technometrics 28 (1986), pp. 3–11]. We optimize this model using a genetic algorithm approach. We also study the effects of the costs and operating parameters on the VSS T ² parameters, and show, through an example, the advantage of economic design over statistical design for VSS T ² charts, and measure the economic advantage of VSS sampling versus fixed sample size sampling.     

Estimating Average Worth of the Selected Subset from Two-Parameter Exponential Populations

ABSTRACT

Suppose independent random samples are available from k(k ≥ 2) exponential populations ∏₁,…,∏ _k with a common location θ and scale parameters σ₁,…,σ _k , respectively. Let X _i and Y _i denote the minimum and the mean, respectively, of the ith sample, and further let X = min{X ₁,…, X _k } and T _i  = Y _i  ? X; i = 1,…, k. For selecting a nonempty subset of {∏₁,…,∏ _k } containing the best population (the one associated with max{σ₁,…,σ _k }), we use the decision rule which selects ∏ _i if T _i  ≥ c max{T ₁,…,T _k }, i = 1,…, k. Here 0 < c ≤ 1 is chosen so that the probability of including the best population in the selected subset is at least P* (1/k ≤ P* < 1), a pre-assigned level. The problem is to estimate the average worth W of the selected subset, the arithmetic average of means of selected populations. In this article, we derive the uniformly minimum variance unbiased estimator (UMVUE) of W. The bias and risk function of the UMVUE are compared numerically with those of analogs of the best affine equivariant estimator (BAEE) and the maximum likelihood estimator (MLE).     

Economic-statistical design of synthetic double sampling T2 chart

Abstract

An economic-statistical design of the synthetic double sampling (synDS) T² chart is presented in this study. The cost function is minimized to obtain the optimal design parameters of the synDS T² chart by incorporating the statistical constraints or the constraints on the average number of samples. An example is provided and a sensitivity analysis is conducted to study the effect of model parameters on the optimal solution of the design. The numerical comparison shows that the synDS T² chart performs better than the synthetic T² chart and the multivariate exponentially weighted moving average chart, in terms of the cost.     

THE CONVERGENCE OF AUTOCORRELATIONS AND AUTOREGRESSIONS1

For a general class of scalar stationary processes, essentially those for which the best linear predictor is the best predictor (in the mean square sense), it is shown that, under fairly minor additional conditions, the sample autocorrelations converge to the true values almost surely and hniformly in the lag, t, at a rate (T^-1log T)^1/2, where T is the sample size. For ARMA processes, if |t|(log T)^a, a < ∞, the rate is the best possible, namely (T^-1log log T)^1/2. In particular the somewhat implausible condition, on the innovations, that E{ε(t)²| F_t-l} is constant is avoided in these results. The theorems are used to discuss autoregressive approximation. When the stationary process is a vector process the condition on the innovation sequence, ε(t), that E{ε(t)ε(t)| F_t-l} be constant, cannot be entirely avoided in relation to autoregressive approximation. This is also discussed.     

Simultaneous marginal survival estimators when doubly censored data is present

A doubly censoring scheme occurs when the lifetimes T being measured, from a well-known time origin, are exactly observed within a window [L, R] of observational time and are otherwise censored either from above (right-censored observations) or below (left-censored observations). Sample data consists on the pairs (U, δ) where U = min{R, max{T, L}} and δ indicates whether T is exactly observed (δ = 0), right-censored (δ = 1) or left-censored (δ = −1). We are interested in the estimation of the marginal behaviour of the three random variables T, L and R based on the observed pairs (U, δ). We propose new nonparametric simultaneous marginal estimators [^(S)]_T, [^(S)]_L{\hat S_{T}, \hat S_{L}} and [^(S)]_R{\hat S_{R}} for the survival functions of T, L and R, respectively, by means of an inverse-probability-of-censoring approach. The proposed estimators [^(S)]_T, [^(S)]_L{\hat S_{T}, \hat S_{L}} and [^(S)]_R{\hat S_{R}} are not computationally intensive, generalize the empirical survival estimator and reduce to the Kaplan-Meier estimator in the absence of left-censored data. Furthermore, [^(S)]_T{\hat S_{T}} is equivalent to a self-consistent estimator, is uniformly strongly consistent and asymptotically normal. The method is illustrated with data from a cohort of drug users recruited in a detoxification program in Badalona (Spain). For these data we estimate the survival function for the elapsed time from starting IV-drugs to AIDS diagnosis, as well as the potential follow-up time. A simulation study is discussed to assess the performance of the three survival estimators for moderate sample sizes and different censoring levels.     

Estimation of the location of a 0-type or ∞-type singularity by Poisson observations

We consider an inhomogeneous Poisson process X on [0, T]. The intensity function of X is supposed to be strictly positive and smooth on [0, T] except at the point θ, in which it has either a 0-type singularity (tends to 0 like |x| ^p , p∈(0, 1)), or an ∞-type singularity (tends to ∞ like |x| ^p , p∈(?1, 0)). We suppose that we know the shape of the intensity function, but not the location of the singularity. We consider the problem of estimation of this location (shift) parameter θ based on n observations of the process X. We study the Bayesian estimators and, in the case p>0, the maximum-likelihood estimator. We show that these estimators are consistent, their rate of convergence is n ^1/(p+1), they have different limit distributions, and the Bayesian estimators are asymptotically efficient.