Ergonomic and individual risk evaluation

The ergonomic risks constitute a vital aspect of study and prevention for the worker's health, especially for people with different capacities. Very job has and implies certain type of risk for the worker's health, depending on the conditions it is done with the use of tools or without them. Aplicated techniques: posturogram, baropodometry, Schober test, biocinemátic chain test, Fukuda test, propioceptiva plataform in personnel with special capabilities.     

Ergonomic evaluation in a values transportation company in Venezuela

The objective was to analyze the work activity and identify risk factors that could account for musculoskeletal disorders in the upper extremities, shoulder and neck of workers of a transport values company in Venezuela. The methods used were: collective interview, tasks observation, evaluation of posture with RULA method and evaluation of repetitive motions with the OCRA method. Five workstations were evaluated. Main problem perceived by workers was: exposure to chemical and biological hazards when handling paper money and coins; inadequate chairs and close supervision. The postures level risk was 1 or 2 for the RULA scale. Only two workstations showed ligth and medium risk level by OCRA method. Conclusion: The factors identified that could explain the musculoskeletal changes were: wrist repetitive flexion and extension, shoulder elevation, lifting weight above shoulder height, elbow repetitive flexion and extension, neck flexion, extended work journey, work overload, high responsibility and strict supervision by a video camera.     

Ergonomic evaluation of a wheelchair transportation securement system

The Americans with Disabilities Act (ADA) specifies guidelines covering the securement system and environment for wheeled mobility device (WhMD) passengers on the public bus system in the United States, referred to as the wheelchair tiedown and occupant restraint system (WTORS). The misuse or disuse of the WTORS system can be a source of injury for WhMD passengers riding the buses. The purpose of this study was to quantify the risks posed to the bus driver while performing the WTORS procedure using traditional ergonomic analysis methods. Four bus drivers completed the WTORS procedure for a representative passenger seated in three different WhMDs: manual wheelchair (MWC), scooter (SCTR), and power wheelchair (PWC). Potential work-related risks were identified using the four most applicable ergonomic assessment tools: PLIBEL, RULA, REBA, and iLMM. Task evaluation results revealed high levels of risk to be present to drivers during the WTORS procedure. The securement station space design and equipment layout were identified as contributing factors forcing drivers to adopt awkward postures while performing the WTORS task. These risk factors are known contributors to injury and the drivers could opt to improperly secure the passengers to avoid that risk.     

Ergonomic considerations in school environments - the need for widening the scope

Behaviour patterns specific to children pose them at greater risk of environmental hazards than adults. Ergonomics is the science of matching human interaction with the proximate environment. Conventionally ergonomic principles were applied on adult work places to ensure safety of the working environment. With emerging scientific evidence, school environments are being a focus to apply ergonomic principles. Children spend more time within schools during critical developmental stages of their life. Everybody feels that the schools are safe places, but they are not. A multitude of ergonomic hazards have been identified in school settings. Widespread mismatches between anthropometry and school furniture, heavy schoolbag carriage and unhealthy bag behaviour are significant. Negative effects range from general tiredness, musculoskeletal pains, spinal deviations, shoulder level shifts, injuries and psychological disturbances. There are fragmented efforts to widen ergonomic concepts to health care professionals and other stakeholders of child health. Addressing ergonomic issues will ensure that children, the future productive generation contributing to economic growth and development of a country, are provided with opportunities in a healthy environment. This paper emphasizes the need for a concerted effort on widening the scope of ergonomics to cater for the evolving demand.     

Ergonomic evaluation of processes and products in the manufacture of upholstery

This study aimed to perform an ergonomic evaluation of industrial processes and products - upholstered sofas - produced in the furniture cluster of Ubá-MG. The used material was collected from two sofas upholstered industries associated with the union of the furniture industries of Ubá region, located in Minas Gerais estate, Brazil. As for the product were evaluated dimensionally 29 upholstered sofas, with 12 being produced by industry "A" and 17 being produced by industry "B". As for the process, were evaluated: the socioeconomic profile of the worker and environmental factors of lighting and noise. The main results of this study showed that the upholstered sofas produced by industries, in general, fulfilled to the recommendations set out in the work in relation to the backrest height and useful seat depth. All the sofas, however, proved to be inadequate in relation to the seat height to the floor and the dimensions of the armrests Regarding environmental aspects, it was observed that in both industries, the activities in most jobs are performed under adverse conditions to the health and safety of workers and nonconformity with the limits set by Brazilian regulatory standard used in this work.     

Ergonomic principles and tools for best interdisciplinary psycho-physical stress prevention

The psycho-physical stress is a risk to all intents and purposes,finally acknowledged, it requires increasing attention. Measures forits protection are reflected in the appropriate application of organizational policies on a human scale, or in respect of the"macro-ergonomics". This work consists on several inter-disciplinary tools available to the proper prevention, outbreaks of work-related stress.During work, adequate rests are important to prevent work related physical and mental fatigue. The strategies for maintaining a healthy balance between work rate and work breaks, may differ depending on the individual, subjective habits and peculiarities related to the work environment. Resting does not necessarily mean "going to break". The break-time is important as the work-time. While the latter is regulated, the first is not always clearly defined, though necessary. Knowing the employment contract is the first step towards the implementation of their rights relating to periods of suspension from the activity of work is also essential for high performance working. Breathing exercises, massage therapy, biofeedback, role-playing are some of the tools used during work breaks to prevent mental and physical fatigue. At the end music has a rhythm by alternating strong and weak accents. If the musical notes represent the "vertical" trend of music (melody), figures and pauses, inserted into the rhythmic structure of the measure, regulate the duration of sounds over time and determine the "horizontal" trend of a song. Transferring this concept on work, is meant to understand, using a metaphor, the importance of respect of changes in both vertical and horizontal trends inside a cycle.     

Ergonomic evaluation of novel tool for snap-off the neck of ampoule

Needlestick and Sharps Injuries (NSI) represent an important workplace issue in contemporary health care. Present study provided the new method to snap-off the neck of sealed ampoule. The idea of novel opener tool is prepare the grinding slice inside rubber ring, so users could put the ampoule inside the rubber ring and then rotated the rubber ring to snap-off the neck of ampoule. The purpose of present study was evaluated the methods of snap-off and sizes of ampoule on forearm muscle activities, wrist postures and performance. The pronator teres muscle were heavier load as increased the sizes of ampoule. For performance analysis, Duncan's multiple range tests indicated that time of snap-off were longer in 10 ml and 20 ml of ampoule. The EMG of pronator teres muscle was significantly affected by methods of snap-off. Duncan's multiple range tests indicated that lower load was experienced on forearm muscles while using grinding slice with glove. For wrist posture, the ranges of motion for wrist were significant lower while using the novel tool. Present study provided the novel tool effectively to snap-off the ampoule to decrease forearm workload and sharp injuries.     

Ergonomic evaluation of laparoendoscopic single-site surgery ports in a validated laparoscopic training model

Although laparoendoscopic single-site surgery (LESS) is feasible among expert laparoscopic surgeons, it poses many technical challenges not seen in conventional laparoscopy (CL). Recent technological advancements in single-incision instrumentation have created more interest and widespread usage of LESS. However, neither LESS nor its novel instrumentation have been thoroughly studied or evaluated using human factors and ergonomics techniques. Consequently, the aim of this study was to compare the physical performance of LESS to CL using a standardized task. Wrist and elbow angular movements, range of motion and physical discomfort were assessed for 24 novice participants. There were no significant differences for physical comfort/discomfort ratings or elbow and wrist flexion/extension range of motion between CL and LESS. However, wrist radial/ulnar range of motion was significantly greater in LESS compared to CL (p < 0.05). Additionally, wrist radial/ ulnar range of motion was significantly greater using the SILS Port compared to the GelPOINT (p < 0.05). Although further investigation is needed, LESS resulted in greater wrist deviation and range of motion due to the close proximity of the instruments, restrictive nature of the single-port devices, and the need to achieve adequate instrument triangulation and visualization.     

Ergonomic factors and production target evaluation in eucalyptus timber harvesting operations in mountainous terrains

There are several forest operations involved in Eucalyptus timber harvesting. This study was carried out during brush-cutting; tree felling, bucking, delimbing, piling and manual extraction operations, with the following objectives: a) analyzing, ergonomically, two systems of brush-cutting: one manual and the other semi-mechanized, using two different machines; b) ergonomically evaluating three different brands of pruner machines used in delimbing felled trees. c) determining the feasible target of productivity as a function of ergonomic factors relevant to establish the time of resting pauses for workers in manual and semi-mechanized timber harvesting systems in mountainous terrain. Brush-cutting, either manual or semimechanized, is an activity carried out prior to timber harvesting. It is usually a hard work, with low productivity when compared with mechanized systems. Pruner machines have been used by forest companies, due to the great possibilities to improve productivity, quality and the health of workers. Ergonomics is a discipline that promotes the adequacy of work to the physical and mental characteristics of human beings, seeking to design production systems and products considering relevant aspects, including social, organizational and environmental factors. Companies should consider the ergonomic factor in the determination of daily worker production targets.     

Ergonomic evaluation of conventional and improved methods of aonla pricking with women workers

Conventional and improved methods of aonla pricking were evaluated ergonomically on an experiment conducted for 20 minute with women workers. The working heart rate, energy expenditure rate, total cardiac cost of work and physiological cost of work with conventional tools varied from 93-102 beats.min-1, 6-7.5 kJ.min-1, 285-470 beats, 14 -23 beats.min-1 while with machine varied from 96-105 beats.min-1, 6.5-8 kJ.min-1 , 336-540 beats, 16-27 beats.min-1 respectively. OWAS score for conventional method was 2 indicating corrective measures in near future while with machine was 1 indicating no corrective measures. Result of Nordic Musculoskeletal Questionnaire revealed that subjects complaint of pain in back, neck, right shoulder and right hand due to unnatural body posture and repetitive movement with hand tool. Moreover pricking was carried out in improper lighting conditions (200-300 lux) resulting into finger injuries from sharp edges of hand tool, whereas with machine no such problems were observed. Output with machine increased thrice than hand pricking in a given time. Machine was found useful in terms of saving time, increased productivity, enhanced safety and comfort as involved improved posture, was easy to handle and operate, thus increasing efficiency of the worker leading to better quality of life.     

Ergonomic analysis for elementary school teachers. Preliminary trial for elementary schools in the province of Buenos Aires

This article presents the results of a preliminary trial, in the context of an intervention, developed by a team of ergonomists under the request of the Occupational Health Department of the General Management of Schools in the Province of Buenos Aires, Argentina. We present a reformulation of the request and the results obtained in 2009 from observations and interviews held in three schools in the province of Buenos Aires in which different jobs positions were assessed. From this stage onwards, the tools were validated and new aspects were shown, particularly in relation to the high variety of real situations in the education sector.     

Ergonomic evaluation of a situation of coexposure to solvents and noise in a printing of flexible packaging

The purpose of this paper is to present an ergonomic evaluation of a situation of co-exposure to solvents and noise in a flexible packaging printer. We discuss how such an approach carried out in the field of printing industry work has made it possible to highlight serious shortcomings in the effectiveness of the prevention actions that are supposed to protect workers from chemicals risks and noise. The ergonomic analysis identified a strain working conditions. Indeed, some jobs expose to noise and toxic risk. Lamination operations, winding and cutting are purveyors of noise. Some physical and spatial factors contribute to amplify the toxic risk. The not wearing of personal protective equipment (PPE) by the operators maybe explained by the fact that it doesn't any possibility to do "otherwise". Indeed, operators adopt a compromise to achieve the objectives of production to the detriment of their health and safety. These constraints are causing gene and psychosocial factors. The interviews revealed a state of psychosis in the workshop, which was accentuated by the reclassification of an operator which has created a climate of panic and anxiety especially for older operators who have more than 20 years exposed to handling of toxic and more exposure to high noise level.     

Ergonomic evaluation of the environment: a case study in a control room of the hydroelectric sector

Representative systematic evaluation studies of the workspace and the extent to which that space is suitable for performing tasks have been developed by professionals engaged on finding evidence as to the importance of users and designers being joint participants in drawing up projects. In this context, this paper sets out to evaluate the environment of a control room in the hydroelectric sector, based on a multidisciplinary method which integrates ergonomics, architecture and environmental psychology so as to assess the influence of space on the user, and thus to identify the user's level of satisfaction with it. It was observed that some adaptation strategies of the space for activities were not implemented satisfactorily, resulting in the need for further studies on making workspaces suitable.     

Ergonomic analysis jobs in recovered factories

With the advent of the deep economic crisis in Argentina on 2001, the recovery of companies through to the creation of the Cooperatives Working Self-Management or Factories Recovered by its workers was constituted as one of the ways in which the salaried disobeyed the increasing unemployment. When the companies turn into recovered factories they tend to leave of side practices that have been seen like imposed by the previous organization and not understanding them as a primary condition for the execution of his tasks. Safety and ergonomics are two disciplines that are no longer considered relevant to the daily work. Therefore this investigation aims to revalue, undergo semantic to give back to a place in every organization analyzed. This research developed a self-diagnostic tool for working conditions, and the environment, present in the recovered factories.     

An evaluation model for school psychological services

An evaluation model is presented which provides a structure and a process for the evaluation of school psychological services. The structure incorporates psychological service areas along required and desired service dimensions; information to evaluate a school psychological service program is gathered from school files and interviews with students, parents, educators, and psychological services personnel. The method involves a five-stage process which may lead toward program modification efforts and subsequent re-evaluation. Further, the need for evaluation models in school psychology and for psychological service evaluation is presented and discussed.     

Establishing validity in evaluation: The Canadian Indian school evaluations

A key concern of evaluators, particularly those using naturalistic procedures, is establishing the validity of the evaluation results. In this article, an approach designed to strengthen the validity of the case study method of evaluation is outlined. Five aspects of this approach are identified that accomplish this. They are the evaluator selection procedure, the method of setting out the evaluation expectations, the use of on-going feedback, the use of multiple perspectives, and the wide involvement of various audiences.