Storage Life Prediction for a High-Performance Capacitor Using Multi-Phase Wiener Degradation Model

Capacitance is a critical performance characteristic of high-voltage-pulse capacitor which is used to store and discharge electrical energy rapidly. The capacitors usually are stored for a long period of time before put into use. Experimental result and engineering experience indicate that the capacitance increases with storage time and will eventually exceed the failure threshold, which means that the capacitor may fail during storage. This is a typical mode of degradation failure for long storage products. Further, the capacitance degradation path can be extrapolated in several stages based on the shifting characteristics. That is, the capacitance increases slowly or fluctuates in the initial storage stage that lasts about three months. Then it increases sharply in the middle stage which lasts about four months. After the two stages, the capacitor enters into the third stage in which capacitance increases constantly. This degradation phenomenon motivates us to study the storage life prediction method based on multi-phase degradation path model. The storage performance degradation mechanism of high-voltage-pulse capacitor was investigated, which provides the physical basis for multi-phase Wiener degradation model. Identification procedure for the transition points in the degradation path was proposed using maximum likelihood principle (MLP). The result of Kruskal-Wallis test which is the method to test whether two populations are consistent or not in statistics showed that the transition points are statistically effective. Other parameters in the multi-phase degradation model are estimated with maximum likelihood estimation (MLE) after the transition points have been specified. The multi-phase Inverse Gaussian (IG) distribution for storage life was deduced for the capacitor, and the point and interval estimation procedure for reliable storage life are constructed with bootstrap method. The efficiency and effectiveness of the proposed multi-phase degradation model is compared with storage life prediction under single-phase condition.     

Zone control charts with estimated parameters for detecting prespecified changes in linear profiles

ABSTRACT

In profile monitoring, control charts are proposed to detect unanticipated changes, and it is usually assumed that the in-control parameters are known. However, due to the characteristics of a system or process, the prespecified changes would appear in the process. Moreover, in most applications, the in-control parameters are usually unknown. To overcome these issues, we develop the zone control charts with estimated parameters to detect small shifts of these prespecified changes. The effects of estimation error have been investigated on the performance of the proposed charts. To account for the practitioner-to-practitioner variability, the expected average run length (ARL) and the standard deviation of the average run length (SDARL) is used as the performance metrics. Our results show that the estimation error results in the significant variation in the ARL distribution. Furthermore, in order to adequately reduce the variability, more phase I samples are required in terms of the SDARL metric than that in terms of the expected ARL metric. In addition, more observations on each sampled profile are suggested to improve the charts' performance, especially for small phase I sample sizes. Finally, an illustrative example is given to show the performance of the proposed zone control charts.     

The estimation of adopted mortality and morbidity rates using model and the phase type law: the Turkish case

Abstract

This paper aims to estimate mortality rate, morbidity-mortality rates of a chronic disease utilizing phase type law in the frame of two and three state processes. The application on commonly used mortality tables in Turkey are adopted to process to estimate the future mortalities with respect to phase type distribution for the purpose of justifying. Using one absorbing state, two and three state Models calculate the time until absorbing of the death and death by phase type distribution for each gender. Consequently, the 3-state probabilities in estimating the mortality-morbidity rates of IHD for Turkish population yield a significant information on the health management and pricing health insurance products.     

Concurrent Design for Process Quality,Statistical Tolerance,and SPC

The rapid response to the requirements of customers and markets promotes the concurrent engineering (CE) technique in product and process design. The decision making for process quality target, SPC method, sampling plan, and control chart parameter design can be done at the stage of process quality plan based on historical data and process knowledge database. Therefore, it is a reasonable trend to introduce the concepts and achievements on process quality evaluation and process capability analysis, CE, and SPC techniques into process plan and tolerance design. A new systematic method for concurrent design of process quality, statistical tolerance (ST), and control chart is presented based on a NSFC research program. A set of standardized process quality indices (PQIs) for variables is introduced for meeting the measurement and evaluation to process yield, process centering, and quality loss. This index system that has relatively strong compatibility and adaptability is based on raisonne grading by using the series of preferred numbers and arithmetical progression. The expected process quality based on this system can be assured by a standardized interface between PQIs and SPC, that is, quality-oriented statistical tolerance zone. A quality-oriented ST and SPC approach that quantitatively specifies what a desired process is and how to assure it will realize the optimal control for a process toward a predetermined quality target.     

Short run spc based upon the second order dynamic linear model for trend detection

Recently, several new applications of control chart procedures for short production runs have been introduced. Bothe (1989) and Burr (1989) proposed the use of control chart statistics which are obtained by scaling the quality characteristic by target values or process estimates of a location and scale parameter. The performance of these control charts can be significantly affected by the use of incorrect scaling parameters, resulting in either an excessive "false alarm rate," or insensitivity to the detection of moderate shifts in the process. To correct for these deficiencies, Quesenberry (1990, 1991) has developed the Q-Chart which is formed from running process estimates of the sample mean and variance. For the case where both the process mean and variance are unknown, the Q-chaxt statistic is formed from the standard inverse Z-transformation of a t-statistic. Q-charts do not perform correctly, however, in the presence of special cause disturbances at process startup. This has recently been supported by results published by Del Castillo and Montgomery (1992), who recommend the use of an alternative control chart procedure which is based upon a first-order adaptive Kalman filter model Consistent with the recommendations by Castillo and Montgomery, we propose an alternative short run control chart procedure which is based upon the second order dynamic linear model (DLM). The control chart is shown to be useful for the early detection of unwanted process trends. Model and control chart parameters are updated sequentially in a Bayesian estimation framework, providing the greatest degree of flexibility in the level of prior information which is incorporated into the model. The result is a weighted moving average control chart statistic which can be used to provide running estimates of process capability. The average run length performance of the control chart is compared to the optimal performance of the exponentially weighted moving average (EWMA) chart, as reported by Gan (1991). Using a simulation approach, the second order DLM control chart is shown to provide better overall performance than the EWMA for short production run applications     

EVVMA and cusum control charts in the presence of correlation

The statistical properties of control charts are usually evaluated under the assumption that the observations from the process are independent. For many processes however, observations which are closely spaced in time will be correlated. This paper considers EWMA and CUSUM control charts for the process mean when the observations are from an AR(1) process with additional random error. This simple model may be a reasonable model for many processes encountered in practice. The ARL and steady state ARL of the EWMA and CUSUM charts are evaluated numerically using an integral equation approach and a Markov chain approach. The numerical results show that correlation can have a significant effect on the properties of these charts. Tables are given to aid in the design of these charts when the observations follow the assumed model.     

Spatial Matching of Multiple Configurations of Points with a Bioinformatics Application

In this article, we present a general model to deal with the problem of matching multiple objects or configurations of points from a Bayesian point of view. We study both labeled and non labeled cases. Our model generalizes, in terms of non singular affine transformations and multiple configurations, previous two-terms matching models. As a practical application in Bioinformatics, we consider data from a microarray experiment of gorilla, bonobo, and human-cultured fibroblasts. We find out the matchings and the best affine transformation between the projections of genes on a two-dimensional space, obtained by a multidimensional scaling technique.     

Probability computations for an extension of the geometric distribution

An extension of the stochastic process associated with the geometric distribution is presented. Combinatorial arguments are used to derive probabilities for various events of interest. Probabilities are approximated by evaluating truncated series. Bounds on the errors of approximation are developed. An example is presented and some additional applications are noted.     

The MLE of Geometric Parameter for a Geometric Process

In this article, we provide the MLE of the ratio parameter of a geometric process and discuss its consistency and asymptotic normality.     

Distribution of busy period in stochastic fluid models

We consider the busy period in a stochastic fluid flow model with infinite buffer where the input and output rates are controlled by a finite homogeneous Markov process. We derive an explicit expression for the distribution of the busy period and we obtain an algorithm to compute it which exhibits nice numerical properties.